VCAT-II Intermediate Vibration Analyst ISO 18346-2 Category II
ENDED
Online Training by
LAD TCI
Inquire Now
Online
/ Training
Details
Learn to be an effective vibration analyst - capable of diagnosing a wide range of faults,
conducting special tests, and performing precision aligning and balancing machinery - with
advanced 3D animations and interactive simulations that make everything easy to understand.
VCAT-II CANDIDATE PROFILE
—
This course is intended for the vibration analyst who will:
• Collect vibration data
• Validate that the data is good
• Set up the analyzer for routine data collection and special tests
• Diagnose most of the common fault conditions
• Perform special tests to validate unbalance, misalignment, resonance, looseness, and other conditions
• Know how to perform precision shaft alignment and balancing
• Use the training and certification as the next step in a rewarding career as a vibration analyst
Compliance:
• Training and certification: ISO 18436-2
• Certification: ISO 18436-1, ISO/IEC 17024
• Training: ISO 18436-3
Exam:
• Three hours
• 100 multiple-choice questions
• 70% passing grade
• Can be taken online or in-person at the course
Certification requirements:
• Training course completed
• 18-months of vibration analysis experience, verified by an independent person
• Pass the exam
• Valid for 5 years
conducting special tests, and performing precision aligning and balancing machinery - with
advanced 3D animations and interactive simulations that make everything easy to understand.
VCAT-II CANDIDATE PROFILE
—
This course is intended for the vibration analyst who will:
• Collect vibration data
• Validate that the data is good
• Set up the analyzer for routine data collection and special tests
• Diagnose most of the common fault conditions
• Perform special tests to validate unbalance, misalignment, resonance, looseness, and other conditions
• Know how to perform precision shaft alignment and balancing
• Use the training and certification as the next step in a rewarding career as a vibration analyst
Compliance:
• Training and certification: ISO 18436-2
• Certification: ISO 18436-1, ISO/IEC 17024
• Training: ISO 18436-3
Exam:
• Three hours
• 100 multiple-choice questions
• 70% passing grade
• Can be taken online or in-person at the course
Certification requirements:
• Training course completed
• 18-months of vibration analysis experience, verified by an independent person
• Pass the exam
• Valid for 5 years
Outline
Review of maintenance practices
Review of condition monitoring technologies
Principles of vibration
• Complete review of basics
• Waveform, spectrum (FFT), phase and orbits
• Understanding signals: modulation, beating, sum/difference
Data acquisition
• Transducer types: Non-contact displacement
Proximity probes, velocity sensors, and accelerometers
• Transducer selection
• Transducer mounting and natural frequency
• Measurement point selection
• Following routes, and test planning
• Common measurement errors
Signal processing
• Filters: Low pass, band pass, high pass, band stop
• Sampling, aliasing, dynamic range
• Resolution, Fmax, data collection time
• Averaging: linear, overlap, peak hold, time synchronous
• Windowing and leakage
Vibration analysis
• Spectrum analysis
• Time waveform analysis (introduction)
• Orbit analysis (introduction)
• Phase analysis: bubble diagrams and ODS
• Enveloping (demodulation), shock pulse, spike energy, PeakVue
Fault analysis
• Natural frequencies and resonances
• Imbalance, eccentricity and bent shaft
• Misalignment, cocked bearing and soft foot
• Mechanical looseness
• Rolling element bearing analysis
• Analysis of induction motors
• Analysis of gears
• Analysis of belt-driven machines
• Analysis of pumps, compressors, and fans
Equipment testing and diagnostics
• Impact testing and bump tests
• Phase analysis
Corrective action
• General maintenance repair activities
• Review of the balancing process
• Review of shaft alignment procedures
Running a successful condition monitoring program
• Setting baselines
• Setting alarms: band, envelope/mask, statistical
• Setting goals and expectations (avoiding common problems)
• Report generation
• Reporting success stories
Acceptance testing
Review of ISO standards
Review of condition monitoring technologies
Principles of vibration
• Complete review of basics
• Waveform, spectrum (FFT), phase and orbits
• Understanding signals: modulation, beating, sum/difference
Data acquisition
• Transducer types: Non-contact displacement
Proximity probes, velocity sensors, and accelerometers
• Transducer selection
• Transducer mounting and natural frequency
• Measurement point selection
• Following routes, and test planning
• Common measurement errors
Signal processing
• Filters: Low pass, band pass, high pass, band stop
• Sampling, aliasing, dynamic range
• Resolution, Fmax, data collection time
• Averaging: linear, overlap, peak hold, time synchronous
• Windowing and leakage
Vibration analysis
• Spectrum analysis
• Time waveform analysis (introduction)
• Orbit analysis (introduction)
• Phase analysis: bubble diagrams and ODS
• Enveloping (demodulation), shock pulse, spike energy, PeakVue
Fault analysis
• Natural frequencies and resonances
• Imbalance, eccentricity and bent shaft
• Misalignment, cocked bearing and soft foot
• Mechanical looseness
• Rolling element bearing analysis
• Analysis of induction motors
• Analysis of gears
• Analysis of belt-driven machines
• Analysis of pumps, compressors, and fans
Equipment testing and diagnostics
• Impact testing and bump tests
• Phase analysis
Corrective action
• General maintenance repair activities
• Review of the balancing process
• Review of shaft alignment procedures
Running a successful condition monitoring program
• Setting baselines
• Setting alarms: band, envelope/mask, statistical
• Setting goals and expectations (avoiding common problems)
• Report generation
• Reporting success stories
Acceptance testing
Review of ISO standards
Speaker/s
Engr. Jesus A. Dimalibot Jr.
Registered Mechanical Engineer, PRC License No. 62407
Certified Vibration Analyst Cat II ISO 18436-2 (Mobius Institute of Australia)
Certified Vibration Analyst Cat III ISO 18436-2 (Mobius Institute of Australia)
Alignment Specialist (Fixturlaser AB Sweden)
Authorized Trainer of Mobius Institute of Australia
Registered Mechanical Engineer, PRC License No. 62407
Certified Vibration Analyst Cat II ISO 18436-2 (Mobius Institute of Australia)
Certified Vibration Analyst Cat III ISO 18436-2 (Mobius Institute of Australia)
Alignment Specialist (Fixturlaser AB Sweden)
Authorized Trainer of Mobius Institute of Australia
Special Offer
** DISCOUNT PROMO:10% off in course for 2-3 pax & 20% for 4 and above. Condition
applies*
applies*
Schedules
Jan 23, 2023 - Jan 27, 2023
ENDED
| Weekdays | 08:00 AM — 05:00 PM |
Online Live
Platform: GoTo Webinar
Platform: GoTo Webinar
Reviews
Be the first to write a review about this course.
Write a Review
LAD TCI is a company that offers quality products, training program and consultancy services for condition-based maintenance, reliability and ISO Management System. LAD TCI specialize in helping organizations optimize their maintenance strategies through the use of the data-driven techniques, designed to improve the overall performances and efficiency of their operations. The Training and certification programs in partnership with Mobius Institute aims to equip professionals with the knowledge and skills needed to effectively implement condition-based maintenance and reliability programs and deliver measurable results.
LAD TCI meticulously collaborates with OEM to provide quality and efficient products that align to improve organizational operations performance.
LAD TCI also offers training and consultancy services for ISO Management system standards in partnership with PECB. LAD TCI provide comprehensive support and guidance for organizations looking to implement and maintain ISO 9001 (Quality Management System), ISO 14001 (Environmental Management System), ISO 55001 (Asset Management System) and ISO 45001 (Occupational health and Safety Management System). LAD TCI services include training programs, audit preparation and support, and consultancy services aimed to helping organizations achieve and maintain ISO certification, and improve their overall management system performance. ...
LAD TCI meticulously collaborates with OEM to provide quality and efficient products that align to improve organizational operations performance.
LAD TCI also offers training and consultancy services for ISO Management system standards in partnership with PECB. LAD TCI provide comprehensive support and guidance for organizations looking to implement and maintain ISO 9001 (Quality Management System), ISO 14001 (Environmental Management System), ISO 55001 (Asset Management System) and ISO 45001 (Occupational health and Safety Management System). LAD TCI services include training programs, audit preparation and support, and consultancy services aimed to helping organizations achieve and maintain ISO certification, and improve their overall management system performance. ...
LAD Training and Certification Inc.
Unit 1007 Entrata Bldg., Alabang, Metro Manila, Philippines 1780
09396309074
